In this guide we will show how to add a Swann DVR or NVR to the SwannView Plus app using the recorder’s UID (unique ID). This UID can be entered manually or by scanning the QR code of your recorder. Once you’ve added the device, you can see the cameras live or playback via your phone SwannView Link app.

‎With Swann Security, everything is controllable via this single app. Swann’s wired security systems, including all of our latest DVR and NVR series, now work seamlessly with wireless solutions such as Swann's new range of Indoor and Outdoor Wi-Fi security cameras. A list of products that work with. SwannEye Plus allows you to view a live stream from your Swann ADS-440u on your Android Phone or Tablet. Easily Pan and Tilt your camera using on-screen gestures, save snapshots of the camera view to your device and even listen to what's happening near your camera using the built in microphone. Note: This app uses a data stream that will.

You need to follow these steps to add the a Swann DVR or NVR to your phone:

1. Install SwannView Plus in your phone
2. Change the stream settings on your DVR or NVR
3. Get the DVR’s network information
4. Add the DVR or NVR to SwannView Plus app by using the QR code

How to add a Swann DVR or NVR on SwannView Plus app via QR code

Install SwannView Plus in your phone

You need the SwannView Plus app to view your cameras on the phone. To download the app, go to Google’s Play Store or Apple’s App Store and search for SwannView Link. Install it and run it on your phone.

Change the stream settings on your DVR or NVR

For smooth live streaming, it is highly suggested to use Substream when playing the videos. You will also need to adjust the substream’s bitrate to an appropriate level for the unit not to consume too much bandwidth. The bit rate depends on your internet’s speed for both the phone and the location where your security system is installed. You may need to play a little bit with various bitrate levels until you are satisfied.

1. Go to Menu > Record.
2. Proceed to Parameters > Substream.
3. Pick a channel on Camera.
4. Set the Video Quality to an appropriate bitrate. The better quality, the higher the bitrate and more slower
5. on the phone. The lower bitrate, the worse the picture quality but it’s smoother on the phone. Find the right balance for your setup.
6. Click on Copy to replicate the settings to other channels. A window will pop up. Tick all checkboxes to select all channels. Click on OK.
7. Click on Apply to save the settings.

Get the DVR’s network information

Which Swann App Do I Need

In this section you’ll learn how to locate the UID of your Swann DVR/NVR (the so called QR code).

1. 1. Access the Main Menu and go to Configuration > Network > General.
      
   2. Check if Enable DHCP is checked. By default, it is checked meaning it is on DHCP.
   3. You can write the UID code for you to have your own copy in case you’re away from the unit. This code the unique ID of your recorder.

Add the DVR or NVR to SwannView Plus app by using the QR code

1. Tap the 3-bar icon located at the top left.
2. Tap the third icon to go to Devices.
3. Tap on the ‘+’ icon at the upper right.
4. Enter the information it needs.
   – Alias: name your system, for example: “My Home”.
   – Register Mode: UID
   – UID: Tap the QR code icon and scan the QR code on top of the unit.
   – User Name: admin
   – Password: type the password of your DVR or NVR
5. Tap on the save ­icon at the top right. If you got any error message, try rebooting the DVR or NVR and your router or modem. Close the app and open it again.
6. Tap on Start Live View to load the cameras.

In this guide we will show how to add a Swann DVR or NVR to the SwannView Plus app using a DDNS address or any other hostname. The idea is that, instead of adding the external IP address of your security system, you can add a domain instead which will self update the IP address when the ISP changes it. Once you’ve added the device, you can see the cameras live or playback via your phone.

You need to follow these steps to add the a Swann DVR or NVR to your phone:

1. Port Forward the Swann’s DVR/NVR ports
2. Install the SwannView Plus app on your phone
3. Change the stream settings on your recorder
4. Set up a DDNS or hostname on your Swann DVR or NVR
5. Adding the DVR/NVR and viewing the cameras on the app

How to view a Swann DVR on SwanView Plus phone app using a DDNS or a domain

Port Forward the Swann’s DVR/NVR ports

You need to make sure that the Server port and HTTP port of your Swann DVR or NVR are open in the router. This procedure is usually called port forwarding and consists of allowing the recorder to communicate with phone apps remotely using certain ports.

The Swann DVR default ports that need to be open are 85, 8000, and 554.

• 85 is the HTTP port
• 8000 is the Server port
• 554 is the RTSP port

Note: You can double check your recorder’s ports if you access your DVR’s menu and go to Configuration > Network > More Settings. You can set any port you want.

To make sure that the ports are opened, check them via an online service such as canyouseeme.org. Enter each port number and hit “Check Port”.

• If it says Error: I could not see your service on on port (85), ( can be any number) then you need to do port forwarding first.
• If it didn’t and only says Success or Succeeded, then it means the port is open. Make sure to check if HTTP port, Server port, and RTSP port are open (all of three).
• If you don’t know how to do port forwarding, just google your router’s model and it’ll show how to do the port forwarding settings.

Install the SwannView Plus app on your phone

SwannView Plus the app where you can view the cameras. To download the app, go to your Google’s Play Store or Apple’s App Store and search for SwannView Plus. Go through the installation process and run it on your phone (or tablet).

Change the stream settings on your Swann DVR/NVR

For smooth live streaming, it is highly suggested to use Substream when playing the videos. We will also need to set the substream’s bitrate to an appropriate level for the unit not to consume too much bandwidth. The bit rate depends on your internet’s speed for both the phone and the location where your security system is installed.

1. Go to Menu > Record.
2. Navigate to Parameters. Then go to the Substream tab.
3. Pick a channel on Camera (do them one by one or use Copy to do it in bulk).
4. Fill out the Video Quality box. The better quality, the higher the bitrate and more slower on the phone. The lower bitrate, the worse the picture quality but it’s smoother on the phone. Find the right balance for your setup.
5. Click on Apply to save the settings.

Set up a DDNS or hostname on your Swann DVR or NVR

In this section, we will show how to set up the DDNS or a hostname for your Swann recorder.

1. Access the Menu > Configuration.
2. Proceed to Network > DDNS.
3. From there, fill up the information needed.
4. Enable DDNS: tick the box.
   – DDNS Type: Choose your domain. If you don’t have a DDNS account yet, you can create your own from any hostname or DDNS website like www.swanndvr.net or www.dyn.com.
   – Server Address: The server of your domain, for example www.swanndvr.net or whatever server you’re using.
   – Device Domain Name: Hostname you registered. For example: myhome. swanndvr.net.
   – Status: This is automatic, you cannot change this; shows the status of your hostname.
   – Username: The username you registered (for the DDNS, not the DVR’s username).
   – Password: The password you created for your DDNS.

Is The Swann App Free

Adding the DVR or NVR to SwannView Plus app

1. Tap the 3-bar icon located at the top left.
2. Tap the 3rd icon to go to Devices.
3. Tap on the ‘+’ icon at the upper right.
4. Change the Register Mode to IP/Domain.
5. Input the information it needs. – Alias: any name that you like such as “My Home”.
   – Address: the ddns address, for example: myhome. swanndvr.net.
   – Port: Server port of the DVR or NVR, the default one is 8000.
   – Username: admin
   – Password: The DVR or NVR’s password.

Tap on the save icon at the top right. if you got any error message, try rebooting the DVR or NVR and your router or modem. Close the app and open it again. Tap on Start Live View to load the cameras.